Parameters for creating an elementary solid. More...

#include <op_shell_parameter.h>

Collaboration diagram for MbElementarySolidParams:

Public Types
enum class	BlockPointType { vertex = 0 , edgeCenter = 1 , faceCenter = 2 }
	The type of point located in the center of the placement of the parallelepiped. More...

Public Member Functions
	MbElementarySolidParams (const MbSNameMaker &operNames)
	Elementary solid parameter constructor. More...

	MbElementarySolidParams (const ElementaryShellType &solidType, const c3d::SpacePointsVector &points, const MbSNameMaker &operNames)
	Elementary solid parameter constructor. More...

	MbElementarySolidParams (const SPtr< const MbElementarySurface > &surface, const MbSNameMaker &operNames)
	Elementary solid parameter constructor. More...

	~MbElementarySolidParams ()
	Destructor.

bool	Init (const ElementaryShellType &solidType, const c3d::SpacePointsVector &points)
	Initialization method for elementary solid parameters. More...

bool	Init (const SPtr< const MbElementarySurface > &surface)
	Initialization method for elementary solid parameters. More...

bool	InitCone (const MbPlacement3D &place, double r1, double r2, bool bHeight, double value)
	Initialization method of elementary solid parameters for cone. More...

bool	InitSphere (const MbPlacement3D &place, double r)
	Initialization method of elementary solid parameters for sphere. More...

bool	InitSphere (const MbArc3D &arc)
	Initialization method of elementary solid parameters for sphere. More...

bool	InitBlock (const MbPlacement3D &place, const MbCartPoint3D &pt, double h1, double h2)
	Method for initializing block body parameters. More...

bool	InitBlock (const MbPlacement3D &place, double dx, double dy, double h1, double h2, BlockPointType pointType)
	Method for initializing block body parameters. More...

bool	InitCylinder (const MbPlacement3D &place, double r, double h1, double h2)
	Method for initializing cylinder body parameters. More...

bool	InitCylinder (const MbArc3D &arc, double h1, double h2)
	Method for initializing cylinder body parameters. More...

const MbSNameMaker &	GetNameMaker () const
	Get the object defining names generation in the operation.

const c3d::SpacePointsVector &	GetPoints () const
	Get the set of points.

const SPtr< const MbElementarySurface > &	GetInitSurface () const
	Get the initial surface.

double	GetOffsetValue () const
	Get offset.

bool	GetIsInvertedValue () const
	Get sign of an inverted body.

Public Attributes
ElementaryShellType	_solidType
	The solid type.

Protected Attributes
c3d::SpacePointsVector	_points
	Set of points.

SPtr< const MbElementarySurface >	_initSurface
	Initial surface.

c3d::SNameMakerSPtr	_operNames
	An object defining names generation in the operation.

Detailed Description

Parameters for creating an elementary solid.

Member Enumeration Documentation

◆ BlockPointType

enum MbElementarySolidParams::BlockPointType

strong

The type of point located in the center of the placement of the parallelepiped.

Enumerator
vertex	Vertex of a parallelepiped.
edgeCenter	Center of the parallelepiped edge directed along the Ox axis.
faceCenter	The center of a face lying in the XY plane.

Constructor & Destructor Documentation

◆ MbElementarySolidParams() [1/3]

MbElementarySolidParams::MbElementarySolidParams ( const MbSNameMaker & operNames )

Elementary solid parameter constructor.

Elementary solid parameters constructor with undefined type.

Parameters

[in] operNames - An object for naming the new objects.

◆ MbElementarySolidParams() [2/3]

MbElementarySolidParams::MbElementarySolidParams	(	const ElementaryShellType &	solidType,
		const c3d::SpacePointsVector &	points,
		const MbSNameMaker &	operNames
	)

Elementary solid parameter constructor.

Constructor of parameters for creating an elementary solid by a set of points.

Parameters

[in]	solidType	- The solid type.
[in]	points	- Set of points.
[in]	operNames	- An object for naming the new objects.

◆ MbElementarySolidParams() [3/3]

MbElementarySolidParams::MbElementarySolidParams	(	const SPtr< const MbElementarySurface > &	surface,
		const MbSNameMaker &	operNames
	)

Elementary solid parameter constructor.

Constructor of parameters for creating an elementary solid by an elementary surface.

Parameters

[in]	surface	- Elementary surface. The acceptable surface types are sphere, torus, cylinder, cone.
[in]	operNames	- An object for naming the new objects.

Member Function Documentation

◆ Init() [1/2]

bool MbElementarySolidParams::Init	(	const ElementaryShellType &	solidType,
		const c3d::SpacePointsVector &	points
	)

Initialization method for elementary solid parameters.

Initialization method for elementary solid parameters by solid type and a set of points.

Parameters

[in]	solidType	- The solid type.
[in]	points	- Set of points.

Returns: Returns true in case of success.

◆ Init() [2/2]

bool MbElementarySolidParams::Init ( const SPtr< const MbElementarySurface > & surface )

Initialization method for elementary solid parameters.

Initialization method for elementary solid parameters by an elementary surface.

Parameters

[in] surface - Elementary surface.
The acceptable surface types are sphere, torus, cylinder, cone.

Returns: Returns true in case of success.

◆ InitCone()

bool MbElementarySolidParams::InitCone	(	const MbPlacement3D &	place,
		double	r1,
		double	r2,
		bool	bHeight,
		double	value
	)

Initialization method of elementary solid parameters for cone.

Initialization method for elementary solid parameters by placement, radiuses of the cone bases and a value that can be the height or angle at the cone vertex.

Parameters

[in]	place	- Placement.
[in]	r1	- Radius of the cone base on the XY plane.
[in]	r2	- Radius of the second cone base, 0 ≤ r2 < r1.
[in]	bHeight	- If true, then a value is a height, else the value is an angle.
[in]	value	- If bHeight = true, then value = height (negative or positive), else value = angle at the cone vertex (between two opposite generatrices), 0 < angle < Pi

Returns: Returns true in case of success.

◆ InitSphere() [1/2]

bool MbElementarySolidParams::InitSphere	(	const MbPlacement3D &	place,
		double	r
	)

Initialization method of elementary solid parameters for sphere.

Initialization method of elementary solid parameters for sphere by placement and radius of the sphere.

Parameters

[in]	place	- Placement.
[in]	r	- Radius of sphere.

Returns: Returns true in case of success.

◆ InitSphere() [2/2]

bool MbElementarySolidParams::InitSphere ( const MbArc3D & arc )

Initialization method of elementary solid parameters for sphere.

Initialization method of elementary solid parameters for sphere by an arc that defines the center, diameter, and placement of the sphere.

Parameters

[in] arc - An arc defining the center, diameter, and placement of a sphere.

Returns: Returns true in case of success.

◆ InitBlock() [1/2]

bool MbElementarySolidParams::InitBlock	(	const MbPlacement3D &	place,
		const MbCartPoint3D &	pt,
		double	h1,
		double	h2
	)

Method for initializing block body parameters.

Method for initializing parameters of a parallelepiped body by placement, diagonal point and heights.

Parameters

[in]	place	- Placement. The center of placement is one of the vertices of the parallelepiped.
[in]	pt	- A point whose projection is the vertex of a parallelepiped lying in the XY plane diagonally relative to the center of the placement.
[in]	h1	- The height of the parallelepiped from the XY plane in the direction of the Z axis.
[in]	h2	- The height of the parallelepiped from the XY plane is opposite to the Z axis.

Returns: - Returns true in case of success.

◆ InitBlock() [2/2]

bool MbElementarySolidParams::InitBlock	(	const MbPlacement3D &	place,
		double	dx,
		double	dy,
		double	h1,
		double	h2,
		BlockPointType	pointType
	)

Method for initializing block body parameters.

Method for initializing the parameters of a parallelepiped body by placement, length, width and heights.

Parameters

[in]	place	- Placement.
[in]	dx	- Length.
[in]	dy	- Width.
[in]	h1	- The height of the parallelepiped from the XY plane in the direction of the Z axis.
[in]	h2	- The height of the parallelepiped from the XY plane is opposite to the Z axis.
[in]	pointType	- Type of point located in the center of the placement: Vertex. Center of the edge directed along the X axis. Center of the lower base.

Returns: - Returns true in case of success.

◆ InitCylinder() [1/2]

bool MbElementarySolidParams::InitCylinder	(	const MbPlacement3D &	place,
		double	r,
		double	h1,
		double	h2
	)

Method for initializing cylinder body parameters.

Method for initializing cylinder body parameters by placement, radius and heights.

Parameters

[in]	place	- Placement.
[in]	r	- Radius.
[in]	h1	- The height of the cylinder from the XY plane in the direction of the Z axis.
[in]	h2	- The height of the cylinder from the XY plane is opposite to the Z axis.

Returns: - Returns true in case of success.

◆ InitCylinder() [2/2]

bool MbElementarySolidParams::InitCylinder	(	const MbArc3D &	arc,
		double	h1,
		double	h2
	)

Method for initializing cylinder body parameters.

Method for initializing the parameters of a cylinder body by base circumference and heights.

Parameters

[in]	arc	- Cylinder base.
[in]	h1	- The height of the cylinder from the XY plane in the direction of the Z axis.
[in]	h2	- The height of the cylinder from the XY plane is opposite to the Z axis.

Returns: - Returns true in case of success.

The documentation for this class was generated from the following file:

op_shell_parameter.h

Public Types

Public Member Functions

Public Attributes

Protected Attributes

Detailed Description

Member Enumeration Documentation

◆ BlockPointType

Constructor & Destructor Documentation

◆ MbElementarySolidParams() [1/3]

◆ MbElementarySolidParams() [2/3]

◆ MbElementarySolidParams() [3/3]

Member Function Documentation

◆ Init() [1/2]

◆ Init() [2/2]

◆ InitCone()

◆ InitSphere() [1/2]

◆ InitSphere() [2/2]

◆ InitBlock() [1/2]

◆ InitBlock() [2/2]

◆ InitCylinder() [1/2]

◆ InitCylinder() [2/2]